|
|
| (One intermediate revision by one other user not shown) |
| Line 1: |
Line 1: |
| {{disputed|date=April 2012}}
| | The writer is known as Irwin. Hiring has been my occupation for some time but I've currently applied for another 1. California is where I've usually been living and I adore each working day living here. To gather badges is what her family and her appreciate.<br><br>Here is my blog post :: [http://www.myprgenie.com/view-publication/weight-loss-tips-that-will-reduce-your-waistline myprgenie.com] |
| | |
| [[Image:RF Intermodulation at 280 MHz.jpg|thumb|288px|A [[frequency spectrum]] plot showing intermodulation between two injected signals at 270 and 275 MHz (the large spikes). Visible intermodulation products are seen as small spurs at 280 MHz and 265 MHz.]]
| |
| | |
| '''Intermodulation''' or '''intermodulation distortion''' ('''IMD''') is the [[amplitude modulation]] of [[Signal (electrical engineering)|signals]] containing two or more different [[frequencies]] in a system with nonlinearities. The intermodulation between each frequency component will form additional signals at frequencies that are not just at [[harmonic]] frequencies ([[integer]] [[multiple (mathematics)|multiple]]s) of either, but also at the sum and difference frequencies of the original frequencies and at multiples of those sum and difference frequencies.
| |
| | |
| Intermodulation is caused by [[non-linear]] behaviour of the [[signal processing]] being used. The [[theoretical]] outcome of these non-linearities can be [[calculate]]d by generating a [[Volterra series]] of the characteristic, while the usual [[approximation]] of those non-linearities is obtained by generating a [[Taylor series]].
| |
| | |
| Intermodulation is rarely desirable in radio or audio processing, as it creates unwanted [[spurious emission]]s, often in the form of [[sidebands]]. For radio transmissions this increases the occupied bandwidth, leading to adjacent channel [[interference (communication)|interference]], which can reduce audio clarity or increase spectrum usage. It should not be confused with [[harmonic distortion]] (which has common [[Distortion (music)|musical applications]]), nor with intentional modulation (such as a [[frequency mixer]] in [[superheterodyne receiver]]s) where signals to be modulated are presented to an intentional nonlinear element ([[Analog multiplier|multiplied]]) (see [[non-linear]] [[Electronic_mixer#Product_mixers|mixers]] such as mixer [[diode]]s and even single-[[transistor]] oscillator-mixer circuits). In audio, the intermodulation products are nonharmonically related to the input frequencies and therefore "off-key" with respect to the common Western musical scale.
| |
| | |
| ==Causes of intermodulation==
| |
| A linear system cannot produce intermodulation. If the input of a [[LTI system theory|linear time-invariant]] system is a signal of a single frequency, then the output is a signal of the same frequency; only the [[amplitude]] and [[Phase (waves)|phase]] can differ from the input signal. However, non-linear systems generate [[harmonic]]s, meaning that if the input of a non-linear system is a signal of a single frequency, <math>~f_a,</math> then the output is a signal which includes a number of integer multiples of the input frequency; (i.e. some of <math>~ f_a, 2f_a, 3f_a, 4f_a, \ldots</math>).
| |
| | |
| Intermodulation occurs when the input to a non-linear system is composed of two or more frequencies. Consider an input signal that contains three frequency components at<math>~f_a</math>, <math>~ f_b</math>, and <math>~f_c</math>; which may be expressed as
| |
| | |
| :<math>\ x(t) = M_a \sin(2 \pi f_a t + \phi_a) + M_b \sin(2 \pi f_b t + \phi_b) + M_c \sin(2 \pi f_c t + \phi_c)</math>
| |
| | |
| where the <math>\ M</math> and <math>\ \phi</math> are the amplitudes and phases of the three components, respectively.
| |
| | |
| We obtain our output signal, <math>\ y(t)</math>, by passing our input through a non-linear function:
| |
| :<math>\ y(t) = G\left(x(t)\right)\,</math>
| |
| | |
| <math>\ y(t)</math> will contain the three frequencies of the input signal, <math>~f_a</math>, <math>~ f_b</math>, and <math>~f_c</math> (which are known as the ''fundamental'' frequencies), as well as a number of [[linear combination]]s of the fundamental frequencies, each of the form
| |
| | |
| :<math>\ k_af_a + k_bf_b + k_cf_c</math>
| |
| | |
| where <math>~k_a</math>, <math>~ k_b</math>, and <math>~k_c</math> are arbitrary integers which can assume positive or negative values. These are the '''intermodulation products''' (or '''IMPs''').
| |
| | |
| In general, each of these frequency components will have a different amplitude and phase, which depends on the specific non-linear function being used, and also on the amplitudes and phases of the original input components.
| |
| | |
| More generally, given an input signal containing an arbitrary number <math>N</math> of frequency components <math>f_a, f_b, \ldots, f_N</math>, the output signal will contain a number of frequency components, each of which may be described by
| |
| | |
| :<math>k_a f_a + k_b f_b + \cdots + k_N f_N,\,</math>
| |
| | |
| where the coefficients <math>k_a, k_b, \ldots, k_N</math> are arbitrary integer values.
| |
| | |
| === Intermodulation order ===
| |
| [[Image:Imps thirdorder.png|thumb|400px|Distribution of third-order intermodulations: in blue the position of the fundamental carriers, in red the position of dominant IMPs, in green the position of specific IMPs.]]
| |
| | |
| The ''order'' <math>\ O</math> of a given intermodulation product is the sum of the absolute values of the coefficients,
| |
| | |
| :<math>\ O = \left|k_a\right| + \left|k_b\right| + \cdots + \left|k_N\right|,</math>
| |
| | |
| For example, in our original example above, third-order intermodulation products (IMPs) occur where <math>\ |k_a|+|k_b|+|k_c| = 3</math>:
| |
| | |
| :<math>\ (f_a + f_b - f_c), (f_a + f_c - f_b), (f_b + f_c - f_a)</math>
| |
| :<math>\ (2f_a - f_b), (2f_a - f_c), (2f_b - f_a), (2f_b - f_c), (2f_c - f_a), (2f_c - f_b)</math>
| |
| | |
| In many radio and audio applications, odd-order IMPs are of most interest, as they fall within the vicinity of the original frequency components, and may therefore interfere with the desired behaviour.
| |
| | |
| ==Passive Intermodulation (PIM)==<!-- This section is linked from [[PIM]] -->
| |
| {{Main|Rusty bolt effect}}
| |
| As explained in [[intermodulation#Causes of intermodulation|a previous section]], intermodulation can only occur in non-linear systems. Non-linear systems are generally composed of ''active'' components, meaning that the components must be biased with an external power source which is not the input signal (i.e. the active components must be "turned on"). Passive intermodulation (PIM), however, occurs in passive devices (which may include cables, antennas etc.) that are subjected to two or more high power tones. The PIM product is the result of the two (or more) high power tones mixing at device nonlinearities such as junctions of dissimilar metals, metal-oxide junctions and even loose connectors. The higher the signal amplitudes, the more pronounced the effect of the nonlinearities, and the more prominent the intermodulation that occurs - even though upon initial inspection, the system would appear to be linear and unable to generate intermodulation.
| |
| | |
| === Sources of PIM ===
| |
| | |
| Ferromagnetic materials are the most common materials to avoid and include ferrites, nickel, (including nickel plating) and steels (including some stainless steels.) These materials exhibit hysteresis when exposed to reversing magnetic fields resulting in PIM generation.
| |
| | |
| PIM can also be generated in components with manufacturing or workmanship defects, such as cold or cracked solder joints or poorly made mechanical contacts. If these defects are exposed to high RF currents, PIM can be generated. As a result, RF equipment manufacturers perform factory PIM tests on components, to eliminate PIM caused by these design and manufacturing defects.
| |
| | |
| In the field, PIM can be caused by components that were damaged in transit to the cell site, installation workmanship issues and by external PIM sources. Some of these include:
| |
|
| |
| * Contaminated surfaces or contacts due to dirt, dust, moisture or oxidation.
| |
| * Loose mechanical junctions due to inadequate torque, poor alignment or poorly prepared contact surfaces.
| |
| * Loose mechanical junctions caused during transportation, shock or vibration.
| |
| * Metal flakes or shavings inside RF connections.
| |
| * Inconsistent metal-to-metal contact between RF connector surfaces caused by any of the following:
| |
| | |
| Trapped dielectric materials (adhesives, foam, etc.), cracks or distortions at the end of the outer conductor of coaxial cables, often caused by overtightening the back nut during installation, solid inner conductors distorted in the preparation process, hollow inner conductors excessively enlarged or made oval during the preparation process.
| |
| | |
| * PIM can also occur in connectors, or when conductors made of two [[Galvanization|galvanically]] unmatched metals come in contact with each other.
| |
| * Nearby metallic objects in the direct beam and side lobes of the transmit antenna including rusty bolts, roof flashing, vent pipes, guy wires, etc.
| |
| | |
| === PIM Testing ===
| |
| IEC 62037 is the international standard for PIM testing and gives specific details as to PIM measurement setups. The standard specifies the use of two +43 dBm (20W) tones for the test signals for PIM testing. This power level has been used by RF equipment manufacturers for more than a decade to establish PASS / FAIL specifications for RF components.
| |
| | |
| == Intermodulation in electronic circuits ==
| |
| Intermodulation is caused by nonlinearity or parameter limitations in an amplifier system. This nonlinearity can be characterized in many ways, including the [[slew rate]], [[crossover distortion]], reduced transistor [[current gain]], or saturation of collector-emitter junctions near clipping. [[Slew-induced distortion]] (SID) can produce intermodulation distortion (IMD) when the first signal is slewing (changing voltage) at the limit of the amplifier's [[power bandwidth]] product. This induces an effective reduction in gain, partially [[Amplitude Modulation|amplitude-modulating]] the second signal. If SID only occurs for a portion of the signal, it is called "transient" intermodulation distortion.<ref name="rane">[http://www.rane.com/par-i.html#IM Rane Pro Audio Reference for IM]</ref> This usually occurs due to [[soft clipping]] of the signal peaks.<ref>http://waltjung.org/PDFs/SID_TIM_TAA77_P1.pdf Slewing Induced Distortion in Audio Amplifiers, Part 1 by Walter Jung in The Audio Amateur Issue 1/1977</ref>
| |
| | |
| == Intermodulation in audio applications ==
| |
| | |
| {{unreferenced section|date=April 2012}}
| |
| | |
| Any system that produces harmonic distortion also produces intermodulation distortion. The difference between the two types of distortion is the '''signal used to test it''', not the device. Only sine waves produce harmonic distortion; music signals always produce intermodulation.
| |
| | |
| {{disputed|date=April 2012}}
| |
| | |
| Audio engineers usually strive to avoid intermodulation, as for anything other than extremely simple input waveforms, it introduces frequency components that are not harmonically related, which tends to sound unmusical and unpleasant. However, certain audio effects rely on [[amplitude modulation]]; these include [[tremolo]] and [[ring modulation]]. One way to generate such effects is through deliberate intermodulation in a non-linear device, but may also be achieved ''without'' intermodulation by an [[analog multiplier]].{{dubious|date=April 2012}} Transient intermodulation distortion, or TIM, occurs in amplifiers that employ negative feedback when signal delays make the amplifier incapable of correcting distortion when exposed to fast, transient signals.
| |
| | |
| [[Harmonic distortion]] occurs when non-linearity (in an [[amplifier]] or [[loudspeaker]], for instance) only creates new frequencies that are harmonically related to the original sine wave signal. Intermodulation distortion occurs when a different type{{dubious|date=April 2012}} of non-linearity can create new frequencies that are ''not'' harmonically related to the original signal. All audio devices give rise to [[distortion]] to some extent; harmonic distortion and intermodulation distortion [[Audio system measurements|tests]] highlight different aspects of imperfections, and one type of distortion may be inaudibly low while the other is significantly high for some equipment under certain conditions.{{dubious|date=April 2012}}{{citation needed|date=April 2012}}
| |
| | |
| In analog recording, [[wow (recording)|wow]] and [[flutter (electronics and communication)|flutter]] are forms of intermodulation distortion caused by speed variations in the medium (usually [[Magnetic tape|tape]]). When the flutter rate is above a certain point, typically about [[Audio frequency|20Hz]], the modulation products impressed into the musical signal no longer present as an audibly obvious flutter, yet continue to interfere with the signal as extraneous [[frequency modulation]], and the resulting sideband products manifest as distortion. This distortion results in a thicker, grainier texture due to the excess non-musical sum and difference components riding above and below the harmonic content of the material.
| |
| | |
| == Measurement ==
| |
| | |
| Intermodulation distortion in audio is usually specified as the [[Root Mean Square]] (RMS) value of the various sum-and-difference signals as a percentage of the original signal's RMS voltage, although it may be specified in terms of individual component strengths, in [[decibel]]s, as is common with [[Radio frequency|RF]] work. Audio IMD [[Audio system measurements|standard tests]] include SMPTE standard RP120-1994<ref name="rane"/> where two signals (at 60 Hz and 7 kHz, with 4:1 amplitude ratios) are used for the test; many other standards (such as DIN, CCIF) use other frequencies and amplitude ratios. Opinion varies over the ideal ratio of test frequencies (e.g. 3:4,<ref>http://www.leonaudio.com.au/3-4.ratio.distortion.measurement.pdf Graeme John Cohen: 3-4 Ratio; A method of measuring distortion products</ref> or almost -but not exactly - 3:1 for example<!-- where was that article?? -->).
| |
| | |
| After feeding the equipment under test with low distortion input sinewaves, the output distortion can be measured by using an [[electronic filter]] to remove the original frequencies, or spectral analysis may be made using [[Fast Fourier transform|Fourier Transformations]] in software or a dedicated [[spectrum analyser]], or when determining intermodulation effects in communications equipment, may be made using the receiver under test itself.
| |
| | |
| Using a modern [[network analyzer (electrical)|network analyzer]] with two internal RF sources and sensitive RF detectors simplifies the measurement setup and also provides a sensitivity level comparable to spectrum analyzers. Furthermore, a calibrated VNA setup also removes mismatch errors from measurements which otherwise would be present in spectrum analyzer measurements.
| |
| Meanwhile error-corrected IM measurement systems are available. These system support frequency converting vector-measurements of S-parameters.<ref name=thala_2009>Thalayasingam, K. and Heuermann, H., ''Novel Vector Non-Linear Measurement System for Intermodulation Measurements'', European Microwave Conference, Rom, Italy, IEEE, 2009,
| |
| [http://ieeexplore.ieee.org/search/searchresult.jsp?newsearch=true&queryText=thalayasingam&x=32&y=12=no Available online]</ref>
| |
| The user can locate IM-sources and perform a vector or time-domain fitting or modelling of the IM-signals and components.
| |
| | |
| == See also ==
| |
| * [[Rusty bolt effect]]
| |
| * [[Beat (acoustics)]]
| |
| * [[Audio system measurements]]
| |
| * [[Second-order intercept point]]
| |
| * [[Third-order intercept point]], a metric of an amplifier or system related to intermodulation
| |
| | |
| == External links ==
| |
| | |
| *{{cite web
| |
| |url=http://users.tpg.com.au/ldbutler/Intermodulation.htm
| |
| |title=Intermodulation Performance and Measurement of Intermodulation Components
| |
| |author= Lloyd Butler
| |
| |year=1997
| |
| |work=VK5BR
| |
| |publisher="Amateur Radio," August 1997
| |
| |accessdate=30 January 2012}}
| |
| | |
| ==References==
| |
| <references/>
| |
| | |
| {{FS1037C MS188}}
| |
| | |
| [[Category:Waves]]
| |
| [[Category:Radio electronics]]
| |