Theta function (disambiguation)

Template:Good article 30 year-old Entertainer or Range Artist Wesley from Drumheller, really loves vehicle, property developers properties for sale in singapore singapore and horse racing. Finds inspiration by traveling to Works of Antoni Gaudí.

The primary line constants are parameters that describe the characteristics of conductive trasmission lines, such as pairs of copper wires, in terms the physical electrical properties of the line. The primary line constants are only relevant to such lines and are to be contrasted with the secondary line constants, which can be derived from them, and are more generally applicable. The secondary line constants can be used, for instance, to compare the characteristics of a waveguide to a copper line, whereas the primary constants have no meaning for a waveguide.

The constants are conductor resistance and inductance, and insulator capacitance and conductance, which are by convention given the symbols R, L, C, and G respectively. The constants are enumerated in terms of per unit length. The circuit representation of these elements requires a distributed element model and consequently calculus must be used to analyse the circuit. The secondary constants of characteristic impedance and propagation constant can be derived in this way.

A number of special cases have particularly simple solutions and important practical applications. Low loss cable requires only L and C to be included in the analysis, useful for short lengths of cable. Low frequency applications, such as twisted pair telephone lines, are dominated by R and C only. High frequency applications, such as RF co-axial cable, are dominated by L and C. Lines loaded to prevent distortion need all four elements in the analysis, but have a simple, elegant solution.

The constants

There are four primary line constants, but in some circumstances some of them are small enough to be ignored and the analysis can be simplified. These four, and their symbols and units are as follows:

Name	Symbol	Units	Unit symbol
loop resistance	R	ohms per metre	Ω/m
loop inductance	L	henries per metre	H/m
insulator capacitance	C	farads per metre	F/m
insulator conductance	G	siemens per metre	S/m

R and L are elements in series with the line (because they are properties of the conductor) and C and G are elements shunting the line (because they are properties of the dielectric material between the conductors). G represents leakage current through the dielectric and in most cables is very small. The word loop is used to emphasise that the resistance and inductance of both conductors must be taken into account. For instance, if a line consists of two identical wires that have a resistance of 25 mΩ/m each, the loop resistance is double that, 50 mΩ/m. Because the values of the constants are quite small, it is common for manufacturers to quote them per kilometre rather than per metre; in the English-speaking world "per mile" can also be used.^[1]^[2]

The word "constant" can be misleading since there is some variation with frequency. In particular, R is heavily influenced by the skin effect. Furthermore, while G has virtually no effect at audio frequency, it can cause noticeable losses at high frequency with many of the dielectric materials used in cables due to a high loss tangent. Avoiding the losses caused by G is the reason many cables designed for use at UHF are air-insulated or foam-insulated (which makes them virtually air-insulated).^[3] The actual meaning of constant in this context is that the parameter is constant with distance. That is the line is assumed to be homogenous lengthwise. This condition is true for the vast majority of transmission lines in use today.^[4]

Typical values for some common cables

Designation	Cable form	Application	R	L^†	G	C	Z₀
			Ω/km	μH/km	nS/km	nF/km	Ω
CAT5^[5]	Twisted pair	Data transmission	176	490	<2	49	100
CAT5e^[6]	Twisted pair	Data transmission	176		<2		100
CW1308^[7]	Twisted pair	Telephony	98		<20
RG59^[8]	Coaxial	Video	36	430		69	75
RG59^[9]	Coaxial (foam dielectric)	Video	17	303		54	75
RG58^[10]^[11]	Coaxial	Radio frequency	48	253	<0.01	101	50
Low loss^[12]	Coaxial (Foam dielectric)	Radio frequency transmitter feed	2.86	188		75	50
DIN VDE 0816^[13]	Star quad	Telephony (trunk lines)	31.8		<0.1	35

† Manufacturers commonly omit a value for inductance in their data sheets. Some of these values are estimated from the figures for capacitance and characteristic impedance by

{Z_{0}}^{2} = L / C

.

Circuit representation

The line constants cannot be simply represented as lumped elements in a circuit; they must be described as distributed elements. For instance "pieces" of the capacitance are in between "pieces" of the resistance. However many pieces the R and C are broken into, it can always be argued they should be broken apart further to properly represent the circuit, and after each division the number of meshes in the circuit is increased. This is shown diagramtically in figure 1. To give a true representation of the circuit, the elements must be made infinitesimally small so that each element is distributed along the line. The infinitesimal elements in an infinitesimal distance $d x$ are given by;^[14]

d L = \lim_{δ x \to 0} (L δ x) = L d x

d R = \lim_{δ x \to 0} (R δ x) = R d x

d C = \lim_{δ x \to 0} (C δ x) = C d x

d G = \lim_{δ x \to 0} (G δ x) = G d x

It is convenient for the purposes of analysis to roll up these elements into general series impedance, Z, and shunt admittance, Y elements such that;

d Z = (R + i ω L) d x = Z d x,

and,

d Y = (G + i ω C) d x = Y d x .

Analysis of this network (figure 2) will yield the secondary line constants: the propagation constant, $γ$ , (whose real and imaginary parts are the attenuation constant, $α$ , and phase change constant, $β$ , respectively) and the characteristic impedance, $Z_{0}$ , which also, in general, will have real, $R_{0}$ , and imaginary, $X_{0}$ , parts, making a total of four secondary constants to be derived from the four primary constants. The term constant is even more misleading for the secondary constants as they all usually vary quite strongly with frequency, even if the frequency dependence of the primary constants is ignored. This is because the reactances in the circuit ( $ω L$ and $1 / (ω C)$ ) introduce a dependence on $ω$ . It is possible to choose specific values of the primary constants that result in $α$ and $Z_{0}$ being constant (the Heaviside condition) but even in this case there is still $β$ which is directly proportional to $ω$ . As with the primary constants, the meaning is that the secondary constants do not vary with distance along the line, not that they are independent of frequency.^[14]^[15]^[16]

Characteristic impedance

The characteristic impedance of a transmission line, $Z_{0}$ , is defined as the impedance looking into an infinitely long line. Such a line will never return a reflection since the incident wave will never reach the end to be reflected. When considering a finite initial length of the line, the remainder of the line can be replaced by $Z_{0}$ as its equivalent circuit. This is so because the remainder of the line is still infinitely long. Considering just the first section of the equivalent circuit of the line (this is an L-network consisting of one element each of $d Z$ and $d Y$ ) the remainder can be replaced by $Z_{0}$ . This results in the network shown in figure 3, which can be analysed for $Z_{0}$ using the usual network analysis theorems,^[17]^[18]

Z_{0} = δ Z + \frac{Z_{0}}{1 + Z_{0} δ Y}

which re-arranges to,

{Z_{0}}^{2} - Z_{0} δ Z = \frac{δ Z}{δ Y}

Taking limits of both sides

\lim_{δ x \to 0} ({Z_{0}}^{2} - Z_{0} δ Z) = {Z_{0}}^{2} = \frac{d Z}{d Y}

and since the line was assumed to be homogenous lengthwise,

{Z_{0}}^{2} = \frac{Z}{Y}

Propagation constant

The ratio of the line input voltage to the voltage a distance $δ x$ further down the line (that is, after one section of the equivalent circuit) is given by a standard voltage divider calculation. The remainder of the line to the right, as in the characteristic impedance calculation, is replaced with $Z_{0}$ ,^[19]^[20]

\frac{V_{i}}{V_{x 1}} = \frac{δ Z + \frac{Z_{0} / δ Y}{Z_{0} + 1 / δ Y}}{\frac{Z_{0} / δ Y}{Z_{0} + 1 / δ Y}} = 1 + \frac{δ Z}{Z_{0}} + δ Z δ Y

Each infinitesimal section will multiply the voltage drop by the same factor. After $n$ sections the voltage ratio will be,

\frac{V_{i}}{V_{x n}} = {(1 + \frac{δ Z}{Z_{0}} + δ Z δ Y)}^{n}

At a distance $x$ along the line, the number of sections is $x / δ x$ so that,

\frac{V_{i}}{V_{x n}} = {(1 + \frac{δ Z}{Z_{0}} + δ Z δ Y)}^{\frac{x}{δ x}}

In the limit as $δ x \to 0$ ,

\frac{V_{i}}{V_{x}} = \lim_{δ x \to 0} \frac{V_{i}}{V_{x n}} = \lim_{δ x \to 0} {(1 + \frac{δ Z}{Z_{0}} + δ Z δ Y)}^{\frac{x}{δ x}}

The second order term $δ Z δ Y$ will disappear in the limit, so we can write without loss of accuracy,

\frac{V_{i}}{V_{x}} = \lim_{δ x \to 0} {(1 + \frac{δ Z}{Z_{0}})}^{\frac{x}{δ x}}

and comparing with the mathematical identity,

e^{x} \equiv \lim_{p \to \infty} (1 + 1 / p)^{p x}

yields,

V_{i} = V_{x} e^{\frac{Z}{Z_{0}} x}

From the definition of propagation constant,

V_{i} = V_{x} e^{γ x}

Hence,

γ = \frac{Z}{Z_{0}} = \sqrt{Z Y}

Special cases

An ideal transmission line will have no loss, which implies that the resistive elements are zero. It also results in a purely real (resistive) characteristic impedance. The ideal line cannot be realised in practice, but it is a useful approximation in many circumstances. This is especially true, for instance, when short pieces of line are being used as circuit components such as stubs. A short line has very little loss and this can then be ignored and treated as an ideal line. The secondary constants in these circumstances are;^[21]

γ = i ω \sqrt{L C}

α = 0

β = ω \sqrt{L C}

Z_{0} = \sqrt{\frac{L}{C}}

Twisted pair

Typically, twisted pair cable used for audio frequencies or low data rates has line constants dominated by R and C. The dielectric loss is usually negligible at these frequencies and G is close to zero. It is also the case that, at a low enough frequency, $R ≫ ω L$ which means that L can also be ignored. In those circumstances the secondary constants become,^[22]

γ \approx \sqrt{i ω C R}

α \approx \sqrt{\frac{ω C R}{2}}

β \approx \sqrt{\frac{ω C R}{2}}

Z_{0} \approx \sqrt{\frac{R}{i ω C}} = \sqrt{\frac{R}{2 ω C}} - i \sqrt{\frac{R}{2 ω C}}

The attenuation of this cable type increases with frequency, causing distortion of waveforms. Not so obviously, the variation of $β$ with frequency also causes a distortion of a type called dispersion. To avoid dispersion the requirement is that $β$ is directly proportional to $ω$ . However, it is actually proportional to $\sqrt{ω}$ and dispersion results. $Z_{0}$ also varies with frequency and is also partly reactive; both these features will be the cause of reflections from a resistive line termination. This is another undesirable effect. The nominal impedance quoted for this type of cable is, in this case, very nominal, being valid at only one spot frequency, usually quoted at 800 Hz or 1 kHz.^[23]^[24]

Co-axial cable

Cable operated at a high enough frequency (VHF radio frequency or high data rates) will meet the conditions $R ≪ ω L$ and $G ≪ ω C$ . This must eventually be the case as the frequency is increased for any cable. Under those conditions R and G can both be ignored (except for the purpose of calculating the cable loss) and the secondary constants become;^[25]

γ \approx i ω \sqrt{L C}

α \approx \frac{L G + R C}{2 \sqrt{L C}} = \frac{1}{2} (Z_{0} G + \frac{R}{Z_{0}}) \approx \frac{R}{2 Z_{0}}

β \approx ω \sqrt{L C}

Z_{0} \approx \sqrt{\frac{L}{C}}

Loaded line

Loaded lines are lines designed with deliberately increased inductance. This is done by adding iron or some other magnetic metal to the cable or adding coils. The purpose is to ensure that the line meets the Heaviside condition by doing which eliminates attenuation and dispersion distortions and ensures that $Z_{0}$ is constant and resistive. The secondary constants are here related to the primary constants by;^[26]

γ = \sqrt{R G} + i ω \sqrt{L C}

α = \sqrt{R G}

β = ω \sqrt{L C}

Z_{0} = \sqrt{\frac{L}{C}} = \sqrt{\frac{R}{G}}

Velocity

The velocity of propagation is given by,

v = λ f .

Since,

ω = 2 π f

and

β = \frac{2 π}{λ}

then,

v = \frac{ω}{β} .

In cases where Buying, selling and renting HDB and personal residential properties in Singapore are simple and transparent transactions. Although you are not required to engage a real property salesperson (generally often known as a "public listed property developers In singapore agent") to complete these property transactions, chances are you'll think about partaking one if you are not accustomed to the processes concerned.

Professional agents are readily available once you need to discover an condominium for hire in singapore In some cases, landlords will take into account you more favourably in case your agent comes to them than for those who tried to method them by yourself. You need to be careful, nevertheless, as you resolve in your agent. Ensure that the agent you are contemplating working with is registered with the IEA – Institute of Estate Brokers. Whereas it might sound a hassle to you, will probably be worth it in the end. The IEA works by an ordinary algorithm and regulations, so you'll protect yourself in opposition to probably going with a rogue agent who prices you more than they should for his or her service in finding you an residence for lease in singapore.

There isn't any deal too small. Property agents who are keen to find time for any deal even if the commission is small are the ones you want on your aspect. Additionally they present humbleness and might relate with the typical Singaporean higher. Relentlessly pursuing any deal, calling prospects even without being prompted. Even if they get rejected a hundred times, they still come again for more. These are the property brokers who will find consumers what they need eventually, and who would be the most successful in what they do. 4. Honesty and Integrity

This feature is suitable for you who need to get the tax deductions out of your PIC scheme to your property agency firm. It's endorsed that you visit the correct site for filling this tax return software. This utility must be submitted at the very least yearly to report your whole tax and tax return that you're going to receive in the current accounting 12 months. There may be an official website for this tax filling procedure. Filling this tax return software shouldn't be a tough thing to do for all business homeowners in Singapore.

A wholly owned subsidiary of SLP Worldwide, SLP Realty houses 900 associates to service SLP's fast rising portfolio of residential tasks. Real estate is a human-centric trade. Apart from offering comprehensive coaching applications for our associates, SLP Realty puts equal emphasis on creating human capabilities and creating sturdy teamwork throughout all ranges of our organisational hierarchy. Worldwide Presence At SLP International, our staff of execs is pushed to make sure our shoppers meet their enterprise and investment targets. Under is an inventory of some notable shoppers from completely different industries and markets, who've entrusted their real estate must the expertise of SLP Worldwide.

If you're looking for a real estate or Singapore property agent online, you merely need to belief your instinct. It is because you don't know which agent is sweet and which agent will not be. Carry out research on a number of brokers by looking out the internet. As soon as if you find yourself certain that a selected agent is dependable and trustworthy, you'll be able to choose to utilize his partnerise find you a house in Singapore. More often than not, a property agent is considered to be good if she or he places the contact data on his web site. This is able to imply that the agent does not thoughts you calling them and asking them any questions regarding properties in Singapore. After chatting with them you too can see them of their office after taking an appointment.

Another method by way of which you could find out whether the agent is sweet is by checking the feedback, of the shoppers, on the website. There are various individuals would publish their comments on the web site of the Singapore property agent. You can take a look at these feedback and the see whether it will be clever to hire that specific Singapore property agent. You may even get in contact with the developer immediately. Many Singapore property brokers know the developers and you may confirm the goodwill of the agent by asking the developer. can be taken as,

β = ω \sqrt{L C}

the velocity of propagation is given by,

v = \frac{1}{\sqrt{L C}} .

The lower the capacitance the higher the velocity. With an air dielectric cable, which is approximated to with low-loss cable, the velocity of propagation is very close to c, the speed of light in vacuo.^[27]

Notes

43 year old Petroleum Engineer Harry from Deep River, usually spends time with hobbies and interests like renting movies, property developers in singapore new condominium and vehicle racing. Constantly enjoys going to destinations like Camino Real de Tierra Adentro.

References

F.R. Connor, Wave Transmission, Edward Arnold Ltd., 1972 ISBN 0-7131-3278-7.
John Bird, Electrical Circuit Theory and Technology, Newnes, 2007 ISBN 0-7506-8139-X.
Ian Hickman, Analog Electronics, Newnes, 1999 ISBN 0-7506-4416-8.
Fred Porges, The Design of Electrical Services for Buildings, Taylor & Francis, 1989 ISBN 0-419-14590-7.

↑ Connor, p.8.
↑ Bird, pp.604-605.
↑ Porges, pp.223-224.
↑ Bird, pp.502-503, 519.
↑ "Bulk cable - Category 5 UTP 4-pair PVC", Molex data sheet, 1999, archived 7 August 2013.
↑ "1583E CAT5E UTP PVC", Belden data sheet 46077, 21 July 1999, archived 7 August 2013.
↑ "CW1308 Internal Telecom Cable", Eland Cables data sheets, archived 8 August 2013.
↑ "8281 Coax - Double Braided RG-59/U Type" Belden data sheet, 14 May 2007, archived 7 August 2013.
↑ "Serial digital video cable", Belden data sheet 1865A, archived 7 August 2013.
↑ "Suhner coaxial cable", Huber & Suhner data sheet, 24 September 2007, archived 7 August 2013.
↑ "RG58/U", General Cable datasheet, pp.74-76.
↑ "7/8" Cellflex Lite Low-Loss Foam-Dielectric Coaxial Cable", RFS datasheet LCF78-50JFNL, 24 October 2006, archived 7 August 2013.
↑ "Trunk cables, paper insulated with aluminium sheath", Nexus datasheet, archived 7 August 2013.
↑ ^14.0 ^14.1 Connor, pp.8-10.
↑ Hickman, p.113.
↑ Porges, p.217.
↑ Porges, pp.216-217.
↑ Connor, pp.10-11.
↑ Connor, pp.9-10.
↑ Bird, pp.609-611.
↑ Connor, p.17.
↑ Connor, pp.18-19.
↑ Bird, pp.612-613.
↑ Porges, p.219.
↑ Connor, p.19.
↑ Connor, pp.19-21.
↑ Connor, pp. 10, 19-20.

[1] Connor, p.8.

[2] Bird, pp.604-605.

[3] Porges, pp.223-224.

[4] Bird, pp.502-503, 519.

[5] "Bulk cable - Category 5 UTP 4-pair PVC", Molex data sheet, 1999, archived 7 August 2013.

[6] "1583E CAT5E UTP PVC", Belden data sheet 46077, 21 July 1999, archived 7 August 2013.

[7] "CW1308 Internal Telecom Cable", Eland Cables data sheets, archived 8 August 2013.

[8] "8281 Coax - Double Braided RG-59/U Type" Belden data sheet, 14 May 2007, archived 7 August 2013.

[9] "Serial digital video cable", Belden data sheet 1865A, archived 7 August 2013.

[10] "Suhner coaxial cable", Huber & Suhner data sheet, 24 September 2007, archived 7 August 2013.

[11] "RG58/U", General Cable datasheet, pp.74-76.

[12] "7/8" Cellflex Lite Low-Loss Foam-Dielectric Coaxial Cable", RFS datasheet LCF78-50JFNL, 24 October 2006, archived 7 August 2013.

[13] "Trunk cables, paper insulated with aluminium sheath", Nexus datasheet, archived 7 August 2013.

[Connor,_pp.8-10-14] 14.0 ^14.1 Connor, pp.8-10.

[15] Hickman, p.113.

[16] Porges, p.217.

[17] Porges, pp.216-217.

[18] Connor, pp.10-11.

[19] Connor, pp.9-10.

[20] Bird, pp.609-611.

[21] Connor, p.17.

[22] Connor, pp.18-19.

[23] Bird, pp.612-613.

[24] Porges, p.219.

[25] Connor, p.19.

[26] Connor, pp.19-21.

[27] Connor, pp. 10, 19-20.

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

[17]

[18]

[19]

[20]

[21]

[22]

[23]

[24]

[25]

[26]

[27]

Theta function (disambiguation)

Contents

The constants

Typical values for some common cables

Circuit representation

Characteristic impedance

Propagation constant

Special cases

Twisted pair

Co-axial cable

Loaded line

Velocity

Notes

References

Navigation menu

Theta function (disambiguation)

The constants

Typical values for some common cables

Circuit representation

Characteristic impedance

Propagation constant

Special cases

Twisted pair

Co-axial cable

Loaded line

Velocity

Notes

References

Navigation menu

Search