Destructive dilemma

In radiometry, photometry and color science, a spectral power distribution (SPD) measurement describes the power per unit area per unit wavelength of an illumination (radiant exitance). More specifically, the concentration as a function of wavelength to any radiometric quantity (e.g. radiant energy, radiant flux, radiant intensity, radiance, irradiance, radiant exitance, radiosity) or photometric quantity (e.g. luminance, luminous flux, luminous intensity, illuminance, luminous emittance).

Knowledge of the SPD is crucial for optical-sensor system applications. Optical properties such as transmittance, reflectivity, and absorbance as well as the sensor response are typically dependent on the incident wavelength.

CIE standard illuminant spectral power distribution comparisons.

Physics of SPD

Mathematically, for the spectral power distribution of a radiant exitance or irradiance one may write:

$M(\lambda )={\frac {\partial ^{2}\Phi }{\partial A\partial \lambda }}\approx {\frac {\Phi }{A\Delta \lambda }}$

where $M(\lambda )$ is the spectral irradiance (or exitance) of the light (SI units: W/m³ = kg/(m·s³)); $\Phi$ is the radiant flux of the source (SI unit: watt, W); $A$ is the area over which the radiant flux is integrated (SI unit: square meter, m²); and $\lambda$ is the wavelength (SI unit: meter, m). (Note that it is more convenient to express the wavelength of light in terms of nanometers; spectral exitance would then be expressed in units of W·m^-2·nm^-1.) The approximation is valid when the area and wavelength interval are small.

Relative SPD

The ratio of spectral concentration (irradiance or exitance) at a given wavelength to the concentration of a reference wavelength provides the relative SPD. This can be written as:

CIE standard illuminant spectral power distribution comparisons referenced to the human visual system photopic response.

$M_{rel}(\lambda )={\frac {M(\lambda )}{M({\lambda _{o}})}}$

For instance, the luminance of lighting fixtures and other light sources are handled separately, a spectral power distribution may be normalized in some manner, often to unity at 555 or 560 nanometers, coinciding with the peak of the eye's luminosity function.

Responsitivity

The SPD can be used to determine the response of a sensor to a specified wavelength. This characterizes the response of signal out to the input power as a function of wavelength. This can be generalized in the following formula:

$R(\lambda )={\frac {S(\lambda )}{M(\lambda )}}$

Knowing the responsitivity is beneficial for determination of illumination, interactive material components, and optical components to optimize performance of a system's design.

Source SPD and Matter

Figure showing the greater proportion of blue light scattered by the atmosphere relative to red light.

The spectral power distribution over the visible spectrum from a source can have varying concentrations of relative SPDs. The interactions between light and matter affect the absorption and reflectance properties of materials and subsequently produces a color that varies with source illumination.

For example, the relative spectral power distribution of the sun produces a white appearance if observed directly, but when the sunlight illuminates the Earth's atmosphere the sky appears blue under normal daylight conditions. This stems from the optical phenomenon called rayleigh scattering which produces a concentration of shorter wavelengths and hence the blue color appearance.

Source SPD and Color Appearance

The human visual response relies on trichromacy to process color appearance. While the human visual response integrates over all wavelengths, the relative spectral power distribution will provide color appearance modeling information as the concentration of wavelength band(s) will become the primary contributors to the perceived color.

This becomes useful in photometry and colorimetry as the perceived color changes with source illumination and spectral distribution and coincides with metamerisms where an object's color appearance changes.

Change in color appearance due to SPD differences in sources.

The spectral makeup of the source can also coincide with color temperature producing differences in color appearance due to the source's temperature.

Color temperature comparison of common electric lamps

See also

• Radiometry
• Photometry (optics)
• Color
• Lighting
• Physical quantities

External links

• Spectral Power Distribution Curves, GE Lighting.